Hello,
I just had a Major Fail on my 1290. The Lid dropped and it's smashed the glass.
Just a little upset as I replaced both the Gas rams last year.
Anyone tell me what type of glass it is, is it anything special or just glass that goes into a thousand bits when it breaks.
Thanks Dynamode
Search found 21 matches
- Wed Dec 07, 2022 5:12 pm
- Forum: General Discussion
- Topic: Broken Glass
- Replies: 1
- Views: 2780
- Fri Nov 01, 2019 9:46 pm
- Forum: General Discussion
- Topic: Card cutting
- Replies: 3
- Views: 7296
Re: Card cutting
Give Manila a try, Soft Card is a bit hit and miss when you Cut it and gives off a lot of Soot. Manila is a harder type of Finish and Cuts really well.
You'll get some good results using it.
Dynamode.
You'll get some good results using it.
Dynamode.
- Thu Nov 01, 2018 8:04 am
- Forum: General Discussion
- Topic: can anyone tell me a good way to mask acrylic?
- Replies: 4
- Views: 5248
Re: can anyone tell me a good way to mask acrylic?
Hello,
Try Transfer Tape, Clear or Paper backed. Make sure you don't have any Bubbles in it, needs to be applied Flat.
Etch and Cut your Image and fill in with what ever you are using, let it dry and Peel it off.
You can buy it on a roll off of ebay. Various Sizes.
Dynamode.
Try Transfer Tape, Clear or Paper backed. Make sure you don't have any Bubbles in it, needs to be applied Flat.
Etch and Cut your Image and fill in with what ever you are using, let it dry and Peel it off.
You can buy it on a roll off of ebay. Various Sizes.
Dynamode.
- Tue Jun 19, 2018 7:31 am
- Forum: General Discussion
- Topic: Antler
- Replies: 2
- Views: 3954
Antler
Hello, Is there anyone who has tried to Laser Etch Antler. I have seen that it can be done, but is it safe to do this and is the Filter System on the 1290 enough to take away the waste or would you need a better system.
Thanks for any Help. Dynamode
Thanks for any Help. Dynamode
- Tue May 22, 2018 8:04 pm
- Forum: General Discussion
- Topic: Quartz Worktop
- Replies: 1
- Views: 3381
Quartz Worktop
Hello,
Can anyone tell me if you can Laser Etch Quartz, I have some off cuts of Worktop.
Has anyone tried it and what sort of results did you get.
Thanks for and advice.
Dynamode.
Can anyone tell me if you can Laser Etch Quartz, I have some off cuts of Worktop.
Has anyone tried it and what sort of results did you get.
Thanks for and advice.
Dynamode.
- Sun Nov 05, 2017 4:10 pm
- Forum: General Discussion
- Topic: MDF
- Replies: 1
- Views: 3797
MDF
Hello, Ever since I purchased my first Laser from HPC, I have been using Ridgeon's 4m MDF, it used to be £7.20p a Sheet, but it has gone through the roof for some reason, it is now £13.58p a Sheet. Has anyone used Slec for MDF, if you are what sort of results have you had from it. The price is a bit...
- Mon Apr 24, 2017 9:14 am
- Forum: General Discussion
- Topic: New tube intallation
- Replies: 4
- Views: 6501
Re: New tube intallation
Hello Cam, If I can pass on some friendly advice, let HPC do it for you, if you get it wrong its a very expensive mistake. It's worth every penny letting them do it. They can sort it in less time, set it up and have you up and running in no time. It's going to cost you more, but if you ask me, money...
- Sat Dec 24, 2016 8:04 am
- Forum: General Discussion
- Topic: birch plywood 0.6>
- Replies: 3
- Views: 6049
Re: birch plywood 0.6>
Hello,
Give Hindleys a try, very good quality and Brilliant Service.
Dynamode
Give Hindleys a try, very good quality and Brilliant Service.
Dynamode
- Wed Nov 09, 2016 8:35 am
- Forum: General Discussion
- Topic: Laminate 1.5
- Replies: 2
- Views: 4478
Laminate 1.5
Hello Out there,
Has any one used HPC Laminate to etch Pictures, if you have, what sort of results did you get.
Thanks for looking.
Dynamode.
Has any one used HPC Laminate to etch Pictures, if you have, what sort of results did you get.
Thanks for looking.
Dynamode.
- Sun Mar 06, 2016 9:08 am
- Forum: General Discussion
- Topic: Couple of questions to all LS3020 users
- Replies: 26
- Views: 25245
Re: Couple of questions to all LS3020 users
Hello, I purchased a new LS3020 from HPC Laser. It's very good bit of Kit. I never had any problems with any of the Perspex, Ply, MDF, that I cut in the two years I used it. When you first get one, you will get the normal things, like setting it up for each project and getting the heat settings righ...