Hello all.
I've had my 3020 since 2013. Used lightly for prototyping and enjoyed the simplicity of it.
However. During a full power job on Friday, it made an odd pop sound (which sounded a bit like when foam catches fire momentarily) so I didn't worry. The job continued and seemed to be fine.
Then I turned the power right down to do some light engraving. The job was destroyed. The laser seemed to be stuck at mid to high power. The control knob has no effect.
Any ideas? Happy to replace any parts.
Thanks in advance.
Hello all. LS 3020 user. Mainly for fun.
-
- Posts: 5
- Joined: Sat Mar 11, 2017 8:17 pm
- Contact:
Re: Hello all. LS 3020 user. Mainly for fun.
Hi - sounds like the potentiometer (power control knob) has blown - give HPC and check with them, they should have spares
Cheers
Dave
Cheers
Dave
Using two LS3060's and an ex 3020 user
Please note I am not employed by HPC, any advice or recomendations I give are based on my own experience and are not necessarily the same as HPC's. First point of contact on any hardware issues should be with HPC
Please note I am not employed by HPC, any advice or recomendations I give are based on my own experience and are not necessarily the same as HPC's. First point of contact on any hardware issues should be with HPC
-
- Posts: 5
- Joined: Sat Mar 11, 2017 8:17 pm
- Contact:
Re: Hello all. LS 3020 user. Mainly for fun.
Thanks Dave.
Have you heard of this before?
Have you heard of this before?
Re: Hello all. LS 3020 user. Mainly for fun.
I know they go wrong sometimes and the symptoms sounds about right but worth confirming with HPC
Using two LS3060's and an ex 3020 user
Please note I am not employed by HPC, any advice or recomendations I give are based on my own experience and are not necessarily the same as HPC's. First point of contact on any hardware issues should be with HPC
Please note I am not employed by HPC, any advice or recomendations I give are based on my own experience and are not necessarily the same as HPC's. First point of contact on any hardware issues should be with HPC
-
- Posts: 5
- Joined: Sat Mar 11, 2017 8:17 pm
- Contact:
Re: Hello all. LS 3020 user. Mainly for fun.
Thank you.
HPC are getting a phone tomorrow first light.
HPC are getting a phone tomorrow first light.
-
- Posts: 5
- Joined: Sat Mar 11, 2017 8:17 pm
- Contact:
Re: Hello all. LS 3020 user. Mainly for fun.
Thanks HPC.
It was the control knob (potentiometer) that had failed. Called on Monday. Fixed by Tuesday 9:30am. In time for me to laser some parts for an F1 team.
Thanks guys.
It was the control knob (potentiometer) that had failed. Called on Monday. Fixed by Tuesday 9:30am. In time for me to laser some parts for an F1 team.
Thanks guys.
Re: Hello all. LS 3020 user. Mainly for fun.
The guys at HPC are good like that
Glad you are back up and running
Best
Dave
Glad you are back up and running
Best
Dave
Using two LS3060's and an ex 3020 user
Please note I am not employed by HPC, any advice or recomendations I give are based on my own experience and are not necessarily the same as HPC's. First point of contact on any hardware issues should be with HPC
Please note I am not employed by HPC, any advice or recomendations I give are based on my own experience and are not necessarily the same as HPC's. First point of contact on any hardware issues should be with HPC
Who is online
Users browsing this forum: No registered users and 1 guest